Logo

P1309 Engine Trouble Code

P1309 Engine

When you check engine light came on code P1309 the reason should be Engine Light ON (or Service Engine Soon Warning Light). However your vehicle's manufacturer may have a different definition for the P1309 OBD-II Diagnostic Powertrain (P) Trouble Code. So you should chech it on our car models.

When your car's 'P1309 Check Engine' light comes on, it's usually accompanied by a sinking feeling in the pit of your stomach. The light could mean a costly problem, like a bad catalytic converter, or it could be something minor, like a loose gas cap. But in many cases, it means at minimum that you'll be visiting the car dealer to locate the malfunction and get the engine conducted light turned off.

P1309 Code Meaning :

P
OBD-II Diagnostic Powertrain (P) Trouble Code For Engine
1
Fuel And Air Metering
3
Fuel Rail Pressure Sensor Circuit Malfunction
0
Cylinder 10 Contribution/balance Fault
9
Ignition Coil A Primary/Secondary Circuit Malfunction

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

P1309 OBD-II Diagnostic Powertrain (P) Trouble Code Description

P1309 OBD-II Trouble Code Misfire Detection Monitor Not enabled is one of the definitions for the P1309; however your vehicles manufacturer may have a different definition for the P1309 code. Please check below for your specif P1309 code. Fuel Rail Pressure Sensor Circuit Malfunction and Cylinder 10 Contribution/balance Fault causes most of code P1309.

Reason For P1309 Code

The reason of P1309 OBD-II Engine Trouble Code is Fuel Rail Pressure Sensor Circuit Malfunction.

Your car parts or components should not be replaced with reference to only a P1309 DTC. The vehicle service manual should be consulted for more information on possible causes of the error code, along with required testing.

How To Repair P1309 Code

Before starting let's see P1309 repairing process steps:

  • Qualified technicians will begin by using a scan tool to access P1309 code stored in the ECU.
  • Technicians will note P1309 code present and any freeze frame data associated with them.
  • After all, if you sure the engine trouble is finished, the code will be cleared.

When detecting a faulty oxygen sensor, your car will be working less efficiently, so it will periodically hold a defective idle, abnormal jerking at an accurate throttle, errors with hard starting, thus all of these symptoms will cause a high fuel consumption that induces you into detecting for an engine light to illuminate.

The computer installed in each fuel-injected vehicle has to be aware of two factors before it can solve the proper cold-start air/fuel compound: the engine coolant temperature and the exterior air temperature. Your symptoms are exactly the same to a faulty engine coolant temperature sensor (ECT). The computer is measuring an air/fuel compound that is excessively meager.

Sometimes P1309 code comes with P130900 code.

Diagnosis Of Engine Error OBD Code P1309

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a P1309 trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the P1309 code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.

The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.

All Engine Trouble Codes

All engine trouble codes with P, U, B and C engine codes.

Code Search

Please fill the "Code Box" to find engine fault code.

Example: 0140

Car Models :

Please select your car.

How To Read Engine Codes ?

Ways to read engine trouble codes.

How To Clear Check Engine Lights ?

Ways to clear check engine light on car panel.

Check Engine Light Dictionary

Ways to clear check engine light on car panel.